Clock Parts at Frankenmuth Clock Company


• Home •Cuckoo Clock Parts • Q & A • Directions & Map • Catalog • Photo Album • Site Map
Tech Support	For questions outside of placing an order tech support is now available; talk to a member of our experienced clock repair staff for the nominal charge of $6.00 for 15 minutes. Please order prior to placing call at 989-652-2933 Monday-Friday 9AM-4:30PM EST
Free Shipping on all order over $60.00
*Clock Oilers and Grease*
	Oiler Long Needle Nose Oiler for all clocks-Windlee's Clock Oil $2.50
	Oiler-Professional Long Needle Nose Oiler for all clocks/thin 1.25 inch flex needle / Synthetic Oil/Nye $5.00
	Mainspring Lube As pictured without needle rather sealing cap for dispensing -enough for 6 mainsprings (2ml) $1.00 each
	Grease Professional About one ounce heavy mainspring and clock grease. For use in areas where clock oiling is too light. In bellows-type dispenser with protective cap. $2.50 each
*Books*
	Clock & Watch Trademark Index An archive of over 35,000 details of trademarks and wordmarks from Switzerland, England, Germany, France and Austria. 989 page Hard cover bound book. Written by Karl Kochman. $42.50
	B-149 One of the greatest and most famous German Clock Factories Gustav Becker Story 1847-1927 by Karl Kochmann $13.95
*German European Base Light Bulbs*
		E-14 (14mm diameter) EUROPEAN SCREW BASE Most often used in German Grandfather Clocks, Cabinets, and larger German Wooden Ornaments 120V, .125 AMPS, 15W, 3,000 LIFE HOURS, C-3A FILAMENT (base is slightly larger than 1/2 inch) $3.50 each
		E-12 (12mm diameter) EUROPEAN SCREW BASE Most often used in German Wooden Ornaments, Pyramids, etc 120V-130V, .125 AMPS, 15W, 3,000 LIFE HOURS, C-3A FILAMENT $2.50 each
		E-10 (10mm diameter) EUROPEAN SCREW BASE Most often used in German Wooden Ornaments and Pyramids 14Volt 3 Watt Light Bulb $1.50 each TEMP OUT OF STOCK
*Suspension Springs* *(order taper pins below if needed)*
	HS248/3 Hermle/Keininger Suspension Spring-Wood Pendulum Grandfather Size Larger than pictured and silver color steel upper and lower blocks. 15/32 inch X 1 inch .09mm Thick $4.00
	HS248/1 Hermle/Keininger Suspension Spring-Lyre (Cable Wind) Grandfather Size15/32 inch X 1 inch. Larger than pictured and silver color steel upper and lower blocks. .07mm Thick $4.00
	HS0062 Suspension Spring-Hermle Grandfather and Large Wall Clocks. Often used on older Ridgeway, Howard Miller and Emperor Grandfather Clocks 5/16 inch X 11/16 inch .05mm Thick $3.00
	HS0060 Suspension Spring-Hermle Wall & Mantle Clocks 5/16 inch X 11/16 inch .04mm Thick $3.00
	US0004 (longer metal flex between blocks) Suspension Spring-Jauch and Urgos pre 1980 Wall, Mantle & Grandfather Clocks 5/16 inch X 23/32 inch .05mm Thick $3.00
	UW-GF Suspension Spring Urgos Grandfather Clock 1-11/16 inch .008inch $7.95
	UW-GM Suspension Spring Urgos Grandmother Clock Smaller of the two 'hook' suspension springs 1-1/8 inch .008 inch $7.95
*Hand Nuts*
	HHN-2 Hermle (German) & Urgos after 1990 Hand Nut Mantle, Mantle & Chain Wind approx one quarter inch $1.00
	HHN-1 Hermle Hand Nut for Grandfather Clocks approx three eighths of an inch $2.00
	UHN-1 Urgos Hand Nut for Grandfather Clocks approx three eighths of an inch $2.50
Quartz Hands
	HH05Q Quartz Movement hands- serpentine style- Size two and three fourth inch. Fits 5 1-2" chapter ring. $1.00
	HH06Q Quartz Movement hands- serpentine style- Size three inches. Fits 6" chapter ring. $1.00
	HH07Q Quartz Movement hands- serpentine style- Size three and seven sixteenth inch. Fits 7" chapter ring $1.00
	HH08Q Quartz Movement hands- serpentine style- Size Four and one sixteenth inch. Fits 8" chapter ring $1.00
	HH07SQ Quartz Movement hands- spade style- Size three and one eighth inch. Fits 7" chapter ring $1.00
	HH09SQ Quartz Movement hands- spade style- Size Four and Five- Sixteenth inch. Fits 9" chapter ring $1.00
Mechanical Hands
	HH06 Mechanical Serpentine hands-Size three inch. Fits 6" chapter ring $5.95
	HH08 Mechanical Serpentine hands-Size 4 inch Fits 8 " chapter ring $5.95
	HH10 Mechanical Serpentine hands-Size 4 3/4 inch. Fits 9-10" chapter ring $5.95
	HH04S Mechanical Spade hands-Size one and three fourths inch. Fits 4" chapter ring $4.95
	HH05S Mechanical Spade hands-Size two and one half inch. Fits 5" chapter ring $4.95
	HH06S Mechanical Spade hands-Size three inch. Fits 6" chapter ring $4.95
	HH07S Mechanical Spade hands-Size three and one half inch. Fits 7" chapter ring $4.95
	HH09S Mechanical Spade hands-Size four and five sixteenth inch. Fits 9" chapter ring $4.95
*Winding Keys*
	Key/4 Size 4 Brass Key for 1970 to present Seth Thomas and Hermle Ships Clock 3.0MM square $3.50
	Key/8 Size 8 Brass Key for most German windup wall & mantel clocks starting from 1960 to 2009. 4mm Square $3.50
	HK/2 Grandfather Clock Winding Crank Size 8 4mm square Fits Most Grandfather Clocks made sine 1974 $12.95
*Door Keys*
	Sligh Grandfather Door Key (May Say Ethan Allen on Key) $9.95
	HM Door Key Howard Miller Grandfather Door Key $5.95
	HM Door Key/2 Howard Miller Door Key Manufactured before 1986 (Notch in Key) $5.95
	HM-Ridgeway Old Style key fits most Ridgeway clocks made before 1984 (Notch in Key) $5.95
	Ridgeway Key Ridgeway Grandfather Door Key $5.95
*Anniversary Clock Domes*
	GD12 Glass Replacement Anniversary Dome for 12 Inch Anniversary (actual size 5.5"X 10.25") $29.95
	GD9 Glass Replacement Anniversary Dome for 9 Inch Anniversary (actual size 4 3/4 X 7 3/4) $23.95
Weights & Weight Shells
	WS40P 40mm x 232mm 1 9/16" x 9 1/8" One polished, brass finished shell with hook, end caps, and center rod. $20.00
	WS40B 40mm x 232mm 1 9/16" x 9 1/8" One brushed, brass finished shell with hook, end caps, and center rod. $28.00
	WS40P 40mm x 264mm One polished, brass finished shell with hook, end caps, and center rod. $28.00
	WS60P 60mm x 245mm 2 3/8" x 9 5/8" One polished, brass finished shell with hook, end caps, and center rod. $28.00
Chain
	HM Chain $9.95 Each w/ends For Hermle Grandfather & Grandmother Clocks 47 Links/ft 70 inch length 1.7mm thickness
	UW Chain $9.95 Each w/ends For Urgos Grandfather & Grandmother Clocks 46.5 Links/ft 56.5inch length 1.6mm thickness
MISCELLANEOUS PARTS
	E-Clips/10 Package of 10 assorted e-clips - generally used on all German movements $0.75
	Taper Pins /12 Package of 12 assorted taper pins- generally used to hold plates together on antique clocks, mount dials to movement & hold suspension spring in place at the top. Steel $1.00
Ratchet Wheel
	HRW380S Hermle Milled Ratchet Winding Wheel for 340 & 350 movements when replacing mainpring $2.00
Barrel Complete
	HBC40 Spring and Barrel (for Hermle 340-020) # stamped on barrel-caution on removal $29.00
	HBC41 Spring and Barrel (for Hermle 340-020) # stamped on barrel-caution on removal $29.00
	HBC50 Spring and Barrel (for Hermle 350, 351or 1151 series) # stamped on barrel-caution on removal $29.00
	HBC52 Spring and Barrel (for Hermle 350, 351 or 1151 series) # stamped on barrel-caution on removal $29.00
	HBC56 Spring and Barrel (for Hermle 350, 351 , or 1151 series) # stamped on barrel-caution on removal $29.00
	HBC11 Spring and Barrel (for Hermle 350 & 351 series) # stamped on barrel-caution on removal $29.00
Movements
All clock movements are subject to a 10% restocking fee.
	HM340/020 340-020 Hermle Westminster movement with bottom hammers. Improved German design $195.00
	HM1050/021 1050-021 HermleTriple Chime Movement With Bottom Hammers $224.00
	HM1050/020 1050-020 HermleTriple Chime Movement With Bottom Hammers $224.00
	HM350/060 350-050 Hermle or Seth Thomas Side Hammer German Movement $209.00
Questions on what to order phone 989-652-2933 or e-mail our parts/repair department

RETURN TO TOP

Last Update June 3, 2009

While Frankenmuth Clock Co. makes every effort to publish accurate figures and product information, it assumes no liability for misinformation found on this web site. Copyright 1999-2008 Frankenmuth Clock Co, Inc . All rights reserved.

Clock Oilers and Grease

Books

Hand Nuts

Quartz Hands

Mechanical Hands

Winding Keys

Door Keys

Anniversary Clock Domes

Weights & Weight Shells